Skip to content
electricistaentrevegas.comReport a fault
Menu

No power at home: we find out why it won't come back and fix it

When the power goes and doesn't come back, or only part of the property is affected, we find the exact point of failure: the consumer unit, the line coming from the meter or a specific circuit. If the outage comes from the street network, we tell you and explain who to report it to.

No power at home: electrician testing the main switch of a consumer unit with all the breakers up

No power or equipment down

No power at home: what it involves

Losing power has two possible origins. If the distribution company's network fails, the whole street or neighbourhood goes dark and it's up to them to fix it. If the fault is in your installation, only your home, the kitchen or the upstairs floor may go off: from the meter output to the last socket, the installation is yours and we repair it.

The most common complaints are “the power's gone but the RCD hasn't tripped” or “the fuses are all up”. With everything up and no power, the fault is usually before the consumer unit: the main switch, a burnt terminal, the fuse on the individual supply line (derivación individual) or the cable running up from the meters. You can't see it; it has to be measured.

We do this in flats, villas, residential buildings, shops, offices and warehouses in Murcia and its outlying districts (pedanías), nearby towns, the Mar Menor and the coast around Torrevieja and Orihuela Costa.

Cases and jobs

Power cuts we fix in homes, residential buildings and businesses

The ones we are asked for most, with an explanation, followed by the other jobs in this service.

The power's gone but the RCD hasn't tripped

There's no power anywhere and everything in the consumer unit is still up. We measure at the input of the main switch: if voltage arrives but doesn't come out, the main switch has damaged contacts and we replace it. If it doesn't arrive, we work backwards along the individual supply line until we find the blown fuse, the loose terminal or the section of cable that has failed.

Half the house without power and the breakers up

When several rooms or all the sockets in one area are off without anything having tripped, there's usually a burnt connection in a junction box, a loose neutral or a breaker that has failed internally, something very common in homes built in the 1970s and 80s. We locate the box where the circuit is cut, remake the connection with new terminals and test the whole line.

Power gone and the RCD won't stay up

If the RCD trips as soon as you push it up, there's a permanent earth leakage. We separate circuits and appliances until we isolate the culprit, usually a water heater, an oven, a washing machine, an outdoor light with water in it or a damp flush-mounted box. We restore power to the rest of the home and repair the leaking item.

Flat without power due to a fault on the individual supply line

Each home in a building is fed by a cable that leaves its meter and runs up to the flat's consumer unit. A loose terminal at the meter output or a joint in a junction box on the landing ends up burning and leaves the home in the dark. We locate the section, replace the cable or the terminal and, if the cable size is now too small for your usage, we suggest upgrading it.

No power after a storm or a blackout

If the street gets its power back and your home stays dark, a breaker or RCD may have been damaged by the surge, a surge protector may have operated or a fuse may have blown. We check every protective device, replace any damaged ones and test the appliances that were plugged in.

More cases we deal with

  • Shop without power at opening time

    Without power there's no shutter, till or shop window. We bring the healthy circuits back into service so you can open, and repair the one that has failed in the consumer unit or in the shop's supply line.

  • Meter cutting out from too much load

    If everything goes off when the oven, washing machine and air conditioning run together without anything tripping in the consumer unit, the meter has cut the supply. We explain how to reset it and spread the loads so it doesn't happen again.

  • Lights work but the sockets don't

    This points to the sockets' protective device or a break in their line. We locate it and repair it without cutting off the rest of the house.

  • Upstairs without power in a villa or duplex

    The break is usually in the line linking the main consumer unit to the upstairs sub-board, or in its protective devices. We measure at both ends and repair the section.

  • Country house or huerta home without power

    With long lines from the meter, power is lost through deteriorated buried joints or cables damaged by rodents. We measure section by section and replace the one that fails.

  • Coastal apartment without power after months closed up

    Damp and salt air corrode the terminals in the consumer unit while nobody is using it. We replace whatever is corroded and test the insulation before switching the power back on.

  • Office without power and computers suddenly off

    We first restore the workstations and the network cabinet, then find what caused the outage, often an overloaded power strip or an added heater.

  • Warehouse that loses power when a machine starts

    If the power cuts every time a compressor or a saw starts, we check the rating of the protective devices, the cable size of the line and the motor's starting system.

  • Main switch hot or smelling of burning

    It has a loose terminal or is working at its limit. We replace the switch and remake its input and output connections.

  • Several homes in the same block without power

    We check the building's main supply line, the centralised meter panel and the output of each individual supply line, and coordinate with the distribution company on anything that is sealed.

  • Kitchen without power after changing the hob or oven

    A more powerful appliance on a circuit that wasn't designed for it trips the protection or burns the connection. We upgrade the line and the protective device and connect it.

What to check before we arrive

Without opening the consumer unit and always with dry hands:

  • Check whether the neighbours, the entrance hall or the street lights have power: if everything is off, the outage is on the network.
  • Note which switches are down and whether the main switch is up.
  • If the RCD trips again as soon as you push it up, don't keep trying: leave it down.
  • Unplug the high-consumption appliances and those that were running when the power went.
  • If you smell burning, see smoke or there's water near the consumer unit, switch off the main switch only if you can do so without standing in water, and move away.

When the outage comes from the distribution company, not your installation

The street network and the lines up to the building's main service fuse box (caja general de protección) belong to the distribution company (distribuidora), which is not the retailer on your contract but the owner of the network. If the whole street is dark, it's for them to deal with: their fault-reporting number is on your bill.

If several homes in the block are affected, the fault may be in the main service fuse box or in the sealed fuses of the centralised meter panel: we tell you whether it's the network or the building and coordinate with the distribution company on what needs to be unsealed. If you see a fallen cable in the street, don't go near it and call the distribution company and 112.

Why the power goes and doesn't come back

There is almost always a connection that has given way. Years of heat loosen the terminals of the main switch, the meter output or the junction boxes, the copper corrodes, especially in homes that are closed up or near the sea, and the connection ends up burning: first it causes occasional cuts and then it stops conducting altogether.

What you get

What you get when we do it

  • We measure, we don't guess

    We follow the voltage from the meter to the point of failure, without changing parts at random.

  • You get back what's working

    We isolate the faulty circuit and the rest of the house works again.

  • You know if it's yours or the network's

    We tell you clearly if the outage is the distribution company's and what to tell them when you report it.

  • We check the rest of the consumer unit

    Neighbouring terminals usually have the same wear as the one that failed.

How we work

How we fix it, step by step

  1. Tell us what happened

    Via the form or by email: what went off, what you see in the consumer unit and whether the neighbours have power.

  2. We locate the break

    We measure at the meter, the main switch, the supply line and each circuit.

  3. We repair it

    We replace the switch, terminal, fuse or damaged section of cable.

  4. We test and explain

    We check all the circuits and tell you what failed and why.

Frequently asked questions

Questions about no power at home

The power has gone at home and won't come back. What should I do first?

Check whether the building or the street has power; if not, it's a network outage and you need to report it to the distribution company. If only your home is affected, push up anything that's down in the consumer unit once, with dry hands. If it trips again, or everything is up and there's still no power, tell us via the form.

The power's gone but the RCD hasn't tripped. Why?

Because the RCD only reacts to earth leakage. If there's no power with everything up, the current is being cut somewhere else: the meter due to excess load, a faulty main switch, a fuse on the supply line or a burnt terminal. It has to be measured to know which.

The fuses are up and I have no power. Is it the electricity company?

If there's no power in the entrance hall or the street either, yes: report it to the distribution company. If the neighbours have power, the fault is almost always between your meter and your consumer unit, and we repair that section.

The power's gone and the RCD won't stay up. Can I force it?

No. If it trips as soon as you push it up, it's detecting a leak and protecting you; insisting can damage it. Unplug your appliances and, if it still won't stay up, leave it down and let us know.

Why do some rooms have power and others don't?

Each area runs on its own circuit. If several rooms are off with everything up, there's a broken connection in a junction box, a loose neutral or a breaker that has failed internally. We find it by measuring box by box.

Do you also deal with outages in shops, offices and warehouses?

Yes. We first get the essentials running so you can work, such as the till, refrigeration, servers or the shutter, and then repair the faulty circuit.

You may also be interested in

Related services

RCD keeps tripping

RCD or breaker tripping with the oven, water heater, air conditioning or for no obvious reason: we test the insulation and eliminate the leak.

See the service

Is it happening right now?

Tell us what is happening, where it is and a phone number. In the meantime, if there is a burning smell, sparks or water, switch off the main switch only if you can do it safely.